Product Details

4 Channel with DSP and Dante(1600W per Channel)

X4

Overview

Powersoft X4 innovates and evolves the concept of the amplification platform though the integration of a worldwide compatible power-box and a full feature DSP inside the power amplifier.

The complete digital audio signal management system based on ARM Cortex A-8 processor and TI C6000 DSP platform heralds new and innovative level of signal processing, providing non-boolean routing and mixing, multi-stage equalization with raised-cosine, IIR and FIR filters, delay up to 4 s in input processing and 200 ms for time alignment, gain and polarity adjustment, crossover, peak limiters, TruePower limiters and Active DampingControl.

The power supply permits worldwide AC acceptance and direct connection to any regional power line configuration: it is now suitable to Single Phase, Bi-Phase or Three Phase operation from 85 VAC up to 440 VAC without need of manual selection. True Three Phase load balancing is directly achievable by the unit without any complex load assignment in the power distribution system design.

Product Higlights

• 1600 Watts per Channel @ 8 Ohms

• 3000 Watts per Channel @ 4 Ohms

• 5200 Watts per Channel @ 2 Ohms

• Channel Routing System

• 3 Phase Power Supply

• Full Featured DSP

• 1U Rack Space

Features

Power supply

Advanced switch-mode power supply permitting worldwide AC acceptance and direct connection to any regional power line configuration.

Suitable to Single Phase, Bi-Phase or Three Phase operation from 85 VAC up to 440 VAC without need of manual selection.

True Three Phase load balancing is directly achievable by the unit without any complex load assignment in the power distribution system design.

Power Factor Correction PFC for extremely low mains consumption and extremely wide mains operating range

Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers

Protections

Fully protected circuit design with:

Innovative operating fault protection aimed to adaptively maintain the system on its SOA by means of the active sensing of the delivered power with respect to the power drawn from the mains.

Realtime output signal measurement and processing in order to derive the actual instantaneous delivered power: all the data are collected and compared to the data about the available stored energy and the available power from the mains. This make the system is immune from any misalignment such as overvoltage, overcurrent, short circuit and so on.

Harmful signal protections: DC, VHF and clipping.

General

6th generation fixed frequency switchmode output stage for high grade sound accuracy

Compact size and high power density

Modular construction allowing for rear panel customization

AES3 digital inputs

Two redundant Dante streams

Settings

Non-boolean channel routing

Input signal backup policy aimed to improve reliability against signal fault

Signal grouping for speaker routing

Built in WiFi remote management

Monitoring

Hardware monitor available for fast local diagnostic

Load impedance measurement / display for each channel

Output power measurements / display for each channel

Mains voltage and current measurements / display

Digital Signal Processing

TI C6000 DSP platform architecture

AD/DA converter: dual 24bit @ 96 kHz Tandem architecture, 127 dB dynamic range, per channel

Input/output independent equalizers per channel providing Raised-cosine, custom FIR, parametric IIR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass

Crossovers: linear phase (FIR), hybrid (FIR-IIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)

Input delay up to 4 s and output delay up to 200 ms for time alignment per channel

Active DampingControl for cable compensation

Power limiter (TruePower, RMS voltage, RMS current) + Peak Limiter

Remote management

Control and monitoring through Armonía Pro Audio Suite

WiFi remote management via smartphone and tablet custom interface

Specifications

GENERAL

Number of channels: 4

Output power

Single channel mode:

2 Ω: 5200 W

4 Ω: 3000 W

8 Ω: 1600 W

Bridge mode:

4 Ω: 10400 W

8 Ω: 6000 W

Max output voltage / current: 175 Vpeak: / 130 Apeak

AC MAIN POWER

Power supply: Universal, Single Phase, Bi-Phase or Three Phase acceptance, switching mode with PFC

Operating voltage: 85 V - 440 V

THERMAL

Operating temperature range: 0° - 45° C - 32° - 113° F

AUDIO

Noise floor: -70 dBV (20 Hz - 20 kHz, A weighted)

THD+N: < 0.5% (typically < 0.01%)

IMD: < 0.5% (typically < 0.01%)

Input impedance: 20 kΩ balanced

Slew rate: > 50 V/mus

Damping factor: > 5000 @ 8 ohm, 20Hz - 500Hz

DSP

DSP architecture: ARM Cortex A-8 processor and TI C6000 DSP platform

AD Converter: Dual 24 bit 96 kHz Tandem architecture with 127 dBA of dynamic range

DA Converter: Dual 24 bit 96 kHz Tandem architecture with 122 dBA of dynamic range

Internal precision: 40 bit floating point

Firmware: Network upgradable firmware

Input equalizer: Raised-cosine, custom FIR, parametric IIR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass

Output equalizer: Raised-cosine, custom FIR, parametric IIR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass

Crossover: Linear phase (FIR), hybrid (FIR-IIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)

Delay: up to 4 s on input section; up to 200 ms per output for time alignment

Limiters: TruePower, RMS voltage, RMS current, Peak limiter

Damping control: Active DampingControl

CONSTRUCTION

Dimensions (L x H x W): 483 mm x 44 mm x 495 mm (19.0 in x 1.7 in x 19.5 in)

Payment

1. Payment by bank transfer with bank account.(ex.BDO, Metro Bank, etc)

2. Payment via PayPal account : PayPal verified account is required.

3. Payment by credit or debit card via PayPal(Visa, Master, JCB, Amex etc.) : PayPal account is NOT required.

4. Payment by credit card(Visa, Master, JCB, Amex etc.) :3D verified credit cards only are eligible for payment by credit card.

5. Payment by bank transfer without bank account.(ex.LBC, Western Union, etc)

 For payment by bank transfer without bank account, the customer may pay by internet banking or telephone banking. The customer may also make payment at local banks. The name of the depositor is required to match the name registered as the depositor when placing the order. Payment shall be made within 7 days from placing the order. The order will be automatically cancelled otherwise.

*Important: All Prices in the website are subject to change without prior notice

Shipping

• Shipping method : LBC, 2GO, Fedex, DHL, EMS, Air21, AP Cargo, JRC, etc
  Covered destinations : Nationwide
  Shipping cost : may vary on destination and purchase amount
  Shipping time estimate : 2~6 business days(in case of in-stock products). Order-based or imported items may take longer to ship. Please inquire by calling the store or via email whether the item is in-stock or order-based.
  Shipment bound for EMS premium regions : The customer may be required to pay additional cost.

  *Important : Products are to be shipped after the payment is made. Please note that shipping may take longer depending on the products of the order.

  
  

   International shipments may be subject to import taxes, duties and customs fees, which are levied once your package reaches the country of destination, and are the responsibility of the recipient. In case that the customer refuses to receive the parcel, the products are to be returned to Philippines and will not be shipped again. According costs(shipping, customs and etc) are the responsibility of the customer and will be deducted from the refund.

  
  

Returns & Exchanges

  Please make sure you have selected right options(e.g. size, color and quantity) prior to completing the order.
Once the order is completed, it is assumed that the customer agreed on our exchange/refund policy.
Exchanges and refunds are accepted only if the exchange/refund request is proven valid for the following reasons.

Eligible for exchanges and refunds:
On condition that the package (Labels, tags) of the products are intact.
-       Sold out products
-       Wrong item delivered
-       Defective products

-       Shoddy Goods

Ineligible for returns and exchanges:
-       Products with customer-induced damages
-       Products whose value is decreased significantly due to elapsed time or other reasons and are not in condition for re-sale
-       Change of mind

* (Please contact us or Email customer service for details)

Exchange/refund procedure
For exchanges/refund, the customer is required to post an exchange/refund request on the “Q&A” board.

The request is to include the reason for exchanges/refunds and the order number.
In case of exchange/refund request due to product defects or wrong item delivered, detailed photos of the products are also required. Exchanges/refunds will be made shortly upon careful examination and confirmation on the reported defects. 

The shipping costs occurring from product defects or wrong item delivered are the responsibility of the channel.com.ph.

>Warranty

channel.com.ph will repair any product under warranty at no charge or replace the unit of the exact model if deemed necessary.

If repair of returned merchandise is necessary due to neglect, damage, misuse, or improper repair by others, a charge will be made for labor, parts, and return freight.

Product Inquiry