Product Details

Overview:

A three-way active line array system, the DB TECNOLOGIES DVA T4 WHITE has set new standards in the sound reinforcement industry since its 2007 market launch.

Better yet, it has brought the benefits of real line array technology to a much wider range of users.

Equipped with top-notch features and engineered for maximum versatility, the DVA T4 delivers premium performance and ensures excellent return on investment.

Main Features:

• Full of Technology
• Modules (meter array) connected to one 16A phase
• Place just 125Kg load on the pick-point
• Fully powered units, freely scalable to setups of any size
• Lossless signal path with no need for speaker cables
• None of the impedance and amp channel availability
• Concerns associated with passive models
• Sequentially configurable array segments
• Digital controller DSP on board
• For utmost operating safety
• Active Line Array 420 Watt RMS

Reliability

The 8“ Neodymium-Woofer is equipped with a high power 2.5“ voice coil to provide superior sound pressure level in a very compact size.

High Efficiency

The 6.5“ Neodymium-Midrange speaker has a sealed basket to provide an optimized volume capacity including high sensitivity and superb sound reproduction.

It also has a horn exit including phase plug for defined and linear sound emission.

State-of-the-Art Drivers

The build in 1”Neodymium- Drivers are equipped with a 1.4” Mylar- Membrane which allow a very quick response and provide a linear frequency range at a surprisingly low weight.

This driver was specially designed for the use with Line- Arrays. Its compact measurements allow very close proximity which is a main factor for minimum interference.

***DVA T4 Black shown

Constant Directivity

The DVA T4 Top is equipped with a constant directivity horn for the High and Mid section and offers a nominal coverage angle of 100°x15°. The CD-Horn provides high flexibility and a good natured attitude if for instance the Array is not aligned correctly. The DVA uses apart from the formation of cylindrical waves (very much dependingon the number of T4 elements) the vector summing of the individual horns. This means that with growing distance to the source (if set up correctly) the listener perceives more and more vector sums of the single elements.However it has to be considered, that the fewer elements are used to spread the sound to a specific area, the stronger must be the curving of them. That’s how the effect of optimised SPL distribution is managed.

Rear Panel Features:

CONTROLS AND FUNCTIONS

1) POWER SWITCH - This switch permits turning the speaker on and off.

2) "MAINS FUSE" FUSE CARRIER - Mains fuse housing.

3) "MAINS INPUT" POWER SOCKET - For connecting the power cable provided. The connector used for mains connection is a POWER CON® (blue)

4) “MAINS OUTPUT LINK” RELAUNCH POWER SOCKET - For relaunching the mains power. The output is connected in parallel with input (3) and can be used to power another amplified speaker.  The connector uses a POWER CON® (grey)

5) " BALANCED INPUT” INPUT CONNECTOR - Balanced input at line level. It is able to accept “XLR” sockets.

6) "BALANCED LINK/OUT ” OUTPUT CONNECTOR - The “XLR” connector connected in parallel with input (5) can be used to send the  input audio signal to another amplified speaker.

7) “INPUT SENS” INPUT SENSITIVITY CONTROL - This control regulates the sensitivity of the signal amplifier input. This control does not affect the “BALANCED LINK/OUT” output level

8) “LIMITER” INDICATOR LIGHT - This indicator comes on red to indicate that the internal limiter circuit has tripped. This prevents amplifier distortion and protects the speakers against overloads.

9) “SIGNAL” INDICATOR LIGHT - This indicator comes on green to indicate the presence of the audio signal (at a level of -20dB).

10) “MUTE/PROT” INDICATOR LIGHT - This yellow indicator indicates amplifier status. In normal operating conditions, the LED is off; if it flashes or is always on, refer to the diagnostics table to check amplifier status.

11) “READY” INDICATOR LIGHT - This indicator comes on green to indicate that the main power voltage is correct. In normal operating conditions, the LED is on; if it flashes or is off, refer to the diagnostics table to check amplifier status.

12) “SET-UP MODE” EQUALIZATION SWITCH - This 10-position rotating switch permits selection of the equalization curve according  to installation type.

Specifications:

Payment

1. Payment by bank transfer with bank account.(ex.BDO, Metro Bank, etc)

2. Payment via PayPal account : PayPal verified account is required.

3. Payment by credit or debit card via PayPal(Visa, Master, JCB, Amex etc.) : PayPal account is NOT required.

4. Payment by credit card(Visa, Master, JCB, Amex etc.) :3D verified credit cards only are eligible for payment by credit card.

5. Payment by bank transfer without bank account.(ex.LBC, Western Union, etc)

 For payment by bank transfer without bank account, the customer may pay by internet banking or telephone banking. The customer may also make payment at local banks. The name of the depositor is required to match the name registered as the depositor when placing the order. Payment shall be made within 7 days from placing the order. The order will be automatically cancelled otherwise.

*Important: All Prices in the website are subject to change without prior notice

Shipping

• Shipping method : LBC, 2GO, Fedex, DHL, EMS, Air21, AP Cargo, JRC, etc
  Covered destinations : Nationwide
  Shipping cost : may vary on destination and purchase amount
  Shipping time estimate : 2~6 business days(in case of in-stock products). Order-based or imported items may take longer to ship. Please inquire by calling the store or via email whether the item is in-stock or order-based.
  Shipment bound for EMS premium regions : The customer may be required to pay additional cost.

  *Important : Products are to be shipped after the payment is made. Please note that shipping may take longer depending on the products of the order.

  
  

   International shipments may be subject to import taxes, duties and customs fees, which are levied once your package reaches the country of destination, and are the responsibility of the recipient. In case that the customer refuses to receive the parcel, the products are to be returned to Philippines and will not be shipped again. According costs(shipping, customs and etc) are the responsibility of the customer and will be deducted from the refund.

  
  

Returns & Exchanges

  Please make sure you have selected right options(e.g. size, color and quantity) prior to completing the order.
Once the order is completed, it is assumed that the customer agreed on our exchange/refund policy.
Exchanges and refunds are accepted only if the exchange/refund request is proven valid for the following reasons.

Eligible for exchanges and refunds:
On condition that the package (Labels, tags) of the products are intact.
-       Sold out products
-       Wrong item delivered
-       Defective products

-       Shoddy Goods

Ineligible for returns and exchanges:
-       Products with customer-induced damages
-       Products whose value is decreased significantly due to elapsed time or other reasons and are not in condition for re-sale
-       Change of mind

* (Please contact us or Email customer service for details)

Exchange/refund procedure
For exchanges/refund, the customer is required to post an exchange/refund request on the “Q&A” board.

The request is to include the reason for exchanges/refunds and the order number.
In case of exchange/refund request due to product defects or wrong item delivered, detailed photos of the products are also required. Exchanges/refunds will be made shortly upon careful examination and confirmation on the reported defects. 

The shipping costs occurring from product defects or wrong item delivered are the responsibility of the channel.com.ph.

>Warranty

channel.com.ph will repair any product under warranty at no charge or replace the unit of the exact model if deemed necessary.

If repair of returned merchandise is necessary due to neglect, damage, misuse, or improper repair by others, a charge will be made for labor, parts, and return freight.

Product Inquiry